The Advanced Intelligent Dual Switch Monitor is an
addressable module for use with the AxisAX Series
Intelligent Fire Alarm Control Panel SLC Loops. Each
module incorporates two (2) independent, individually
programmable, initiating device circuits (IDC), providing
cost-effective solutions in areas requiring multiple
addresses.
The IDC circuits are each capable of monitoring a
single contact device or a group of devices. Contacts
can be normally open (N.O.) or normally closed (N.C.)
ranging from heat detectors, linear heat detectors,
4-wire conventional smoke detectors, waterfl ow
switches, tamper switches, manual pull stations, switch
input points for control, or any other supervised input
requirement. Though each IDC circuit can monitor
any number of contact devices, it is not recommended
to mix alarm, supervisory, or security contacts on the
same IDC circuit. Each initiating device circuit is
separately addressed and can be wired Class A or B.
A typical application for the Dual Switch Monitor would
be the individual monitoring of waterfl ow and tamper
switches located at a sprinkler system riser.
Incorporated with each individual IDC circuit is a built-in
priority interrupt feature which allows rapid response
capabilities from highly critical contact devices (e.i.,
manual pull stations, etc.).
Two (2) eight position programming DIP switches are
provided on each Dual Switch Monitor for IDC circuit
addressing and wiring classifi cation defi nition. The
module mounts to the front of a standard 4” square
or 2-gang electrical outlet box. Displayed on the
front of each module are two (2) red status LEDs that
independently illuminate steady during active condition
of the associated IDC circuit.
Compatible with the AxisAX Series Dynamix I/O
relationship programming, the Dual Switch Monitor
can be individually assigned to any input type and
programmed to activate any output relationship, output
group, timing function, gated function, etc. to perform
project specifi c monitoring and control operations.
Features:
• Two Independent Initiating Device Circuits (IDC)
• Class A or B Wiring
• Dedicated IDC Activation Status LEDs
Listings and Approvals:
• ETL ANSI/UL 864 Listed: 3118002NYM-001B
• UL fi le: UOXX.S7003 / ML fi le: S24460
• CSFM Approved: 7300-1713:112
Unique Features:
• 4” Square or 2-Gang Electrical Box Mounting
• Flexible Programmablity
• Duarable Construction
• Cost-Effective & Trouble-Free Installation
• Integral Priority Interrupt
Advanced Fire Systems Inc
100 South Street, Hopkinton, MA 01748
Tel: (508) 435-9995
Fax: (508) 435-9990
Email: [email protected]
Web: www.advancedco.com
As our policy is one of constant product improvement the right is therefore
reserved to modify product specifi cations without prior notice.
www.advancedco.com
903-002 Rev. 1.3 Page 2 of 2
L1
L2
– +
–
+
To Next
AX Series
Peripheral
From
AX Series
SLC Loop
Programming
DIP Switches
Class “A” (Style D) Wiring
AA+
A/BA/B+
AA+
A/BA/B+
AA+
A/BA/B+
12345678
8
4
2
1
64
32
16
NO
B
WIRING
CLASS
A
1
0
SWITCH MONITOR 2
SWITCH MONITOR 1
12345678
8
4
2
1
64
32
16
NO
B
WIRING
CLASS
A
1
0
E
O
L
Class “B” (Style B) Wiring 47K
1/2 Watt
E
O
L
Class “B” (Style B) Wiring 47K
1/2 Watt
TB2
TB3
TB1
Ordering Information
55000-790ADV Dual Switch Monitor
Dual Switch Monitor Specifi cations
Voltage 17-28 VDC, w/Communication Pulses 5-9 VDC
Operating Current
Quiescent
Alarm
w/LED’s
0.85 mA
0.85 mA
5.85 mA
Line Impedance 100 Ω
Wiring Classifi cation Class A or Class B
End-of-Line Resistor 47 KΩ, 0.5 Watt (Class “B” only)
Wiring Screw In-Out Terminals
Mounting 4” Square or 2-Gang Electrical Outlet Box
Dimensions (Diameter & Height) 41/2”W x 41/2”H x 1”D
Weight 2.8 oz
Operating Temperature 320
-1200 F (00
-490 C)
Humidity 10-93% (non-condensing)
Dual Switch Monitor – 550
advancedco |
